Ground Engaging Tools
Ground engaging tools are consumables — they are meant to wear so the bucket does not. We stock the full wear package: teeth in general-purpose, rock chisel, tiger and penetration profiles, the adapters and pins that hold them, cutting edges, end bits, side cutters, shrouds and weld-on wear protection.
Pranthi Enterprise supplies ground engaging tools and wear parts from Surat, Gujarat — bucket teeth, weld-on and bolt-on adapters, flex and roll pins, cutting edges, end bits, side cutters, lip and heel shrouds, chocky bar, ripper points and grader blades.
What we supply
Bucket teeth 8 lines
Fits Excavator, Backhoe Loader and Wheel Loader.
-
General Purpose Tooth
Balanced profile for mixed digging
-
Rock Chisel Tooth
Narrow chisel profile for rock and hard ground
-
Tiger Tooth
Twin-point tooth for maximum penetration
-
Twin Tiger / Multi-Point Tooth
Multiple points for very hard material
-
Penetration Tooth
Long sharp tip for compacted material
-
Heavy Duty Abrasion Tooth
Thick section for high-wear quarry work
-
Flare Tooth
Wide flared profile for loading and clean-up
-
Long Tip Tooth
Extended tip for trenching
Adapters, pins and retainers 9 lines
Fits Excavator, Backhoe Loader and Wheel Loader.
-
Weld-On Adapter
Adapter welded to the bucket lip
-
Bolt-On Adapter
Bolted adapter, no welding required
-
Centre Adapter
Adapter for intermediate lip positions
-
Corner Adapter
Adapter for the bucket corners
-
Flex Pin
Rubber-loaded pin retaining tooth to adapter
-
Vertical Pin and Retainer
Vertical locking system
-
Horizontal Pin and Retainer
Horizontal locking system
-
Roll Pin
Split spring pin for tooth retention
-
Rubber Retainer / Lock
Elastomer lock washer for pins
Edges, bits and cutters 11 lines
Fits Backhoe Loader, Wheel Loader, Bulldozer, Motor Grader and Excavator.
-
Cutting Edge — Flat
Straight bolt-on edge
-
Cutting Edge — Curved
Curved profile edge for buckets
-
Cutting Edge — Single Bevel
One-sided bevel, reversible
-
Cutting Edge — Double Bevel
Two-sided bevel for longer life
-
Serrated Edge
Toothed edge for penetration in hard ground
-
Segment Edge
Short bolt-on sections for large buckets
-
End Bit — LH / RH
Protects the outer corner of the edge
-
Corner Bit / Half Arrow
Angled corner protection
-
Side Cutter — LH / RH
Bolt-on protection for bucket sides
-
Bucket Lip / Lip Plate
Replaceable front lip section
-
Base Edge
Main structural edge of the bucket
Shrouds, wear plate and protection 7 lines
Fits Excavator, Wheel Loader, Backhoe Loader, Bulldozer, Motor Grader, Soil Compactor and Crane.
-
Lip Shroud
Protects the lip between teeth
-
Heel Shroud
Protects the bucket heel from wear
-
Wear Plate / Liner Plate
Abrasion-resistant plate for bucket floors
-
Chocky Bar
Weld-on wear bar for high-abrasion areas
-
Wear Button / Wear Runner
Small weld-on wear protection
-
Bucket Protector
General weld-on protective element
-
Hardfacing Electrode
Consumable for wear repair by welding
Ripper and grader wear parts 12 lines
Fits Excavator, Bulldozer, Motor Grader and Soil Compactor.
-
Ripper Shank
Structural shank holding the ripper point
-
Ripper Point
Replaceable ripping tip
-
Ripper Shank Protector
Wear guard for the shank
-
Ripper Pin and Retainer
Point fixing hardware
-
Grader Blade — Curved
Curved mouldboard blade
-
Grader Blade — Flat
Flat mouldboard blade
-
Grader End Bit
Blade corner protection
-
Grader Serrated Edge
Toothed edge for hard surfaces
-
Mouldboard Wear Plate
Protects the mouldboard face
-
Circle Wear Insert / Shim
Wear components in the grader circle
-
Scarifier Shank and Tip
Ripping tines ahead of the blade
-
Compactor Wheel Tip / Cleat
Bolt-on pads for padfoot compactors
Fasteners 3 lines
Fits Excavator, Backhoe Loader, Wheel Loader, Bulldozer, Motor Grader, Soil Compactor and Crane.
-
Plough Bolt and Nut
Countersunk bolt for edges and wear parts
-
Track Head Bolt
Special head bolt for GET fixing
-
Flat Washer / Lock Washer
Fixing hardware
Common questions
Which tooth profile should I use?
General purpose suits mixed digging; rock chisel and tiger profiles give penetration in rock and hard ground; flare teeth suit loading and clean-up on wheel loaders. Tell us the machine and the material on WhatsApp and we will advise.
Do teeth and adapters have to be the same brand?
They have to be the same system — a tooth is designed to fit a specific adapter nose and pin. Send us a photo of the existing adapter and we will match it.
Do you supply grader blades and scarifier tips?
Yes. Curved and flat mouldboard blades, end bits, serrated edges, mouldboard wear plate, circle wear inserts and scarifier shanks and tips are all listed here.
Can you supply cutting edges cut to length?
Cutting edges are supplied in standard flat, curved, single-bevel, double-bevel, serrated and segment forms. Send the length, thickness and bolt pattern you need and we will confirm what we can source.
Other categories
Catalogue last updated: 16 September 2026 · WhatsApp +91 90540 40111 for availability and lead time.
Need a price on ground engaging tools?
Send the part and your machine on WhatsApp and we'll come back with availability, price and lead time — same day in business hours.